Modern Lubricating Greases

« Back to Previous Page
0
0

Modern Grease making has moved away from the old conventional processes. I am trying to take a comprehensive view on...

Please to read the entire article.

Marked as spam
Posted by Vishnu Sarma (Discussions: 1, Comments: 1)
Replied on September 30, 2017 12:00 am
Category: Used Oil Analysis
9 views
0
Private comment
I think more that technology the cost factors are important..After UK says by 2040 no fossil fuels so more and more electric vehicles and more expensive Lithium ..Do we have alternate to Lithium..Thay will be more challenging...
Marked as spam
Posted by PREM NIDHI MISHRA (Discussions: 0, Comments: 2)
Replied on September 29, 2017 8:00 pm
0
Private comment
Oxidation Stability, Penetrometer, Grease Worker, Roll Stability , Oil Seperation IP 121, Drop point test Apparatus, Corrosion Preventive Properties Appratus, Water washout tester, 4ball weld load, Low temp tester appratus...
Process could be open kettle or Closed kettle (Stratco) depends on type of greases to be made.. Deareator is one of the important equipment but small grease mfg don't use it..
Homogenizer is more or less a show piece in the grease plants.. Close kettle reduces the mfging time but cooling kettle should be preferably open to reduce batch process time..
Marked as spam
Posted by Kapil Pahwa (Discussions: 0, Comments: 2)
Replied on September 29, 2017 8:00 pm
0
Private comment
Thanks, Kapil. You have shown your interest in Grease making.
Marked as spam
Posted by Vishnu Sarma (Discussions: 1, Comments: 1)
Replied on September 30, 2017 8:00 pm
0
Private comment
Still a lot to learn from you sir.. I miss your mentoring...
Marked as spam
Posted by Kapil Pahwa (Discussions: 0, Comments: 2)
Replied on September 30, 2017 8:00 pm
0
Private comment
Dear Sir, Really lot of things we have to learn, Sir, you or anyone please guide me regarding a job in the gulf area or in a Singapore. I have an experience, Thanks
Marked as spam
Posted by MusTafa KhAn QaMar WaRsI (Discussions: 0, Comments: 3)
Replied on October 2, 2017 8:00 pm
0
Private comment
Kettle Utilisateur avec stenless steel...Ni
Marked as spam
Posted by Flavien Jean-Jacques Jaovelo (Discussions: 0, Comments: 7)
Replied on October 2, 2017 8:00 pm
0
Private comment
Good morning. If you just want to test different thickener Systems, how would you proceed?
Marked as spam
Posted by Thomas Myrdek (Discussions: 0, Comments: 1)
Replied on October 3, 2017 8:00 pm
0
Private comment
We are looking for Turnkey solution for 10MT/CD capacity modern Grease Plant ( (70% Li base ) here in Bangladesh with complete know how.Any recommendation , guidance & interest will be highly appreciated .
Marked as spam
Posted by Md. Luthful Bari (Discussions: 0, Comments: 1)
Replied on October 3, 2017 8:00 pm
0
Private comment
Future may not be very bright for lubricating oil, but grease will flourish. Automobile segment is moving towards electric vehicles, earth moving / construction / agriculture equipment are also moving towards electric and environmental concern on used lubricants are increasing. Future will have low volume engine oil, transmission oil, differential oil, hydraulic oil.....

It is time to think of new types of grease , which is out of the box capable of decreasing re-greasing frequency, ultra long life, lithium free, environmentally friendly etc. Also need to have better systems to reduce contamination, smart health monitoring systems of greases for optimizing re-greasing interval.
Marked as spam
Posted by Anjeeve George (Discussions: 0, Comments: 2)
Replied on October 3, 2017 8:00 pm
0
Private comment
Open kettle may save processing time, but result may be a dirtier grease that increases abrasive and fatigue wear rates in the end-use equipment. Current testing of new greases using ASTM D7918 show some new packaged greases with very high foreign particulate levels. Also, dewatering of soaps is critical for long bearing life. Some new greases with >1000 ppm H2O levels routinely when QC checked with D7918 testing for moisture.
Marked as spam
Posted by Rich Wurzbach (Discussions: 1, Comments: 1)
Replied on October 4, 2017 8:00 pm
0
Private comment
please help me to develop the transparent grease, and the formulation and the ingredient
Marked as spam
Posted by MUHAMMAD SHABEER (Discussions: 0, Comments: 1)
Replied on October 8, 2017 8:00 pm
« Back to Previous Page